Zhengzhou Fusmar Machinery is a professional charcoal briquette machine manufacturer, this article will introduce the charcoal briquette machine considerations in detail. Charcoal briquette machine is a device that processes various branches, straws, trunks, etc. through a series of steps to eventually carbonize them into a charcoal briquette. The charcoal briquette produced by the charcoal press machine has high density and good flammability. It can replace fuelwood and coal, which is very beneficial for saving resources and environmental protection.
Charcoal BriquetteRaw Material Moisture Control
The charcoal briquette production line mainly includes a crusher, a dryer, a charcoal press machine, and a carbonization furnace. These configurations work together to complete the mechanism charcoal process. The raw materials of the mechanism charcoal are mainly used the peanut shell, sawdust, sawdust and etc. Charcoal press machine has strict requirements on the moisture content of raw materials. The moisture requirement of the charcoal making machine for the raw materials must control within 12%. The charcoal making machine has higher requirements on the moisture content of the raw materials in the production process, and the moisture content of the raw materials is generally between 6% and 12%. If the moisture content is <6%, the conversion of raw materials and viscosity are poor, and the charcoal briquettes are not strong. If the water content is >12%, the charcoal briquettes are soft and easy to bend and cracks easily, and the density is small. The detection of the moisture of the raw material of the charcoal briquette machine is difficult to observe by the naked eye and is usually roughly identified by hand feeling. First, we touched the working separator shell by hand, and the temperature made the hand feel hot. Next, look at the color of the material just coming out and need to yellow. After grabbing a handful of the material, use your palm to make it into a group, then let it go, and need all the raw materials to be scattered. Therefore, users who invest in charcoal briquette machine must pay special attention to charcoal technology issues. If the raw material moisture is not up to standard, it is necessary to configure suitable drying equipment. The material with suitable moisture will produce a higher yield and better flammability when producing charcoal.
Why Charcoal Briquette Machine Out Of The Bar
The charcoal briquette machine is mainly used to produce charcoal briquette. The charcoal bar produced by the charcoal briquette machine can successfully replace natural charcoal for industrial and domestic use. The charcoal making machine will always be affected by some of the actual production processes. These factors will affect the normal operation of the charcoal making machine. For example, charcoal briquette machine out of the bar or the bar is not molding. The charcoal briquette machine out of the bar because the humidity of the raw material is too large, and the heating temperature of the raw material charcoal briquette machine is not increased according to the requirements of use. The heating temperature of the charcoal briquette machine is entrained in the spiral tank of the charcoal machine, and the heating cylinder is covered with a groove. Reinstalled with the groove of the heating cylinder, the power supply voltage of the charcoal briquette machine is low, the inner sleeve of the bracket is worn better, and the auger is worn and repaired. The reason why the charcoal bar not molding is that the humidity of the charcoal press machine principle is too large. Heat out the moisture, and then dry it through the dryer to reach a certain moisture requirement. The angle of the charcoal propeller should be less than 20 degrees. The electric thermocouple of the grinding propeller should be inspected and installed according to the installation position. The heating coil should be checked regularly to ensure slack.
Mechanism Charcoal Environmental Protection And Energy-saving
The mechanism charcoal adopts environmental protection and energy-saving technology, which can solve environmental problems and use the dryer to dry the raw materials, thereby saving fuel costs. Using the mechanism of charcoal raw material drying technology, using electronic temperature control can achieve the ideal dry humidity, automatic discharge, and the output is large and the power consumption is low, the effect is very good. The reason why the mechanism charcoal is widely used, mainly the mechanism charcoal has many advantages. For example, compared with other charcoal, the mechanism charcoal is cheap, and has no dirt beam, does not explode, and has its own fixed shape. The most important thing is very environment friendly. In the course of use, there is basically no waste slag or waste liquid, exhaust gas, etc. So that basically no environmental pollution is caused after use, which is particularly prominent compared with other carbons.
Zhengzhou Fusmar Machinery has a strong technical force. With long-term practical experience, concentrating on research and design. The equipment is well configuration, the gap, and the size design is reasonable, and the performance is stable.
We not only provide a good product, but also provide high quality service. If you are interested in our products,
you can contact us in the following ways.
.jpg)
.jpg)
.jpg)
